無軸螺旋輸送機的組織結構和原理
無軸螺旋輸送機主要由驅動裝置、頭部裝配、機殼、無軸螺旋體、槽體襯板、進料口、出料口、機蓋(需要時)、底座等組成。
驅動裝置:采用擺線針輪輪減速機或軸裝式硬齒面齒輪減速機,設計時應盡可能將驅動裝置設在出料口端,使螺旋體在運轉時處在受拉狀態。頭部裝配有推力軸承,可承受輸送物料時產生的軸向力。
機殼:機殼為U型或O型,上部加防雨型機蓋,材質有不銹鋼或碳鋼或玻璃鋼。
無軸螺旋體:材質為不銹鋼或碳鋼。
槽體襯板:材質為耐磨的塑料板或橡膠板或鑄石板等。進、出料口:有方形和圓形兩種,一般進、出料口形式由用戶決定。
The shaft-less screw conveyor is mainly composed of driving device, head assembly, casing, shaft-less screw, groove liner, inlet, outlet, machine cover (when needed), base, etc.
Drive device: Adopt cycloid pinwheel reducer or axle-mounted hard-tooth face gear reducer. When designing, the drive device should be set at the outlet as far as possible, so that the spiral body is in tension state during operation. The head is equipped with thrust bearings, which can bear the axial force generated when conveying materials.
Hull: The hull is U-shaped or O-shaped, with a rain-proof cover on the top, made of stainless steel or carbon steel or FRP.
Shaftless helicoid: stainless steel or carbon steel.
Trough lining: material is wearable plastic plate or rubber plate or cast stone plate. There are two kinds of inlet and outlet: the square and the round. The general inlet and outlet forms are determined by the users.
相關資訊
- 對GX型管式螺旋輸送機
- 如何處理機械格柵運行
- 機械格柵停機后要做的
- 新科源機械格柵排放量
- 機械格柵的設計方案必
- 看看機械格柵對細菌處
- 無軸螺旋運送機廣泛應
- 改變機械格柵除污機流
- 無軸螺旋輸送機本質不
- 新科源機械格柵用鏈板
- 無軸螺旋輸送機中螺旋
- 改變機械格柵除污機流
- 螺旋輸送機葉片損壞的
- 如何改變機械格柵除污
- 傾斜無軸螺旋輸送機在
- 城市污水的處理該常使
- 埋刮板輸送機的工作原
- 機械格柵在應用過程中
- 介紹無軸螺旋輸送機無
- 機械格柵和傳統設備相
- 螺旋輸送機運行遇到下
- 無錫新科源機械格柵設
- 螺旋輸送機的摩擦力關
- 機械格柵對加工業的發
- 對無軸螺旋輸送機質量
- 不銹鋼材質的機械格柵
- 無軸螺旋輸送機在污泥
- 螺旋輸送機出現堵料的
- 螺旋輸送機在污泥處理
- 螺旋輸送機螺旋葉片形
- 對不銹鋼耙齒清污機的
- 分析下機械格柵配件容
- 無軸螺旋葉片結構的動
- 無軸螺旋輸送機出現堵
- 機械格柵除污機到底是
- 無軸螺旋輸送機型號分
- 機械格柵的升級減小了
- 無軸螺旋輸送機在輸送
- 機械格柵在設計時應考
- 無軸螺旋輸送機運行過
- 機械格柵
- 無軸螺旋輸送機的組織
- 機械格柵在食品加工廠
- 無軸螺旋葉片輸送機特
- 無軸螺旋輸送機使用的
- 新科源環保介紹不銹鋼
- 機械格柵在城市污水處
- 無軸螺旋輸送機常見問
- 格柵除污機施工檢查方
- 回轉式格柵機的工作原